average crushing value of aggregate

Standard of Crushing Value of Coarse Aggregates for ...

Jan 20, 2020· Crushing resistance of coarse aggregate is the key to the stability and durability of the skeleton structure of permeable asphalt (PA) mixture. To determine the technical requirements of crushing value of coarse aggregate used in PA mixture, step-loading compression tests were conducted on the mixtures of PA-13 and a control asphalt mixture AC-13, respectively.

Aggregate Crushing Value Test – Determine Aggregate ...

May 17, 2019· Concept and significance of the Aggregate crushing value test. The ' aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load …

Aggregate crushing value test | Step by Step Procedure ...

The average crushing value in the different tests is the actual crushing value of aggregate. Important points to remember. It is recommended that the crushing value of aggregate should be less than 30%. If it is more than 30 % then 10% finer aggregate is suggested to use. The aggregate whose crushing value is less than 30% can be used for ...

average crushing value of aggregate in kosovo

Aggregate crushing value test Step by Step Procedure . 11/08/2020 This test is repeated once or twice and the average crushing value of the aggregate is determined The average crushing value in the different tests is the actual crushing value of aggregate Important points to remember It is recommended that the crushing value of aggregate should be less than 30% If it is more than 30 % …

Calculate the average crushing value of aggregate using ...

Sep 21, 2019· For observation III: %ACV= 598 3184 X 100 =18.78%. To find average crushing value of given aggregate. Average %ACV = ( 18.43 + 17.89 + 18.78) / 3 X 100. Average %ACV = 18.36%. Suitability: As the % ACV is 18.36%,which is less than 30%, hence the given sample of aggregate is suitable for non-wearing surfaces like roadways, runways etc.

(PDF) Testing aggregates - Part 110: Methods for ...

The values given in Table 4 apply when a test result is obtained as the average of two determinations of the aggregate crushing value on sub-samples of the same test portion, when both determinations comply with the check on the masses given in 7.4.

Aggregate Crushing Value Test - Significance & Test ...

The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the IS sieve 2.36mm and the weight of the dried aggregate sample. At least three samples should be tested from the same batch and average value to get accurate results.

Lab Test on Aggregates at Site - CivilJungle

Procedure of Aggregate Crushing Value. Take a sample of aggregates by sieving through 12.5mm and retained on 10mm. The aggregate shall be tested in dry surface conditions. If dried by heating, the period of drying shall not exceed 4 hours and temp shall be 100-110 deg C.

Stone Aggregate Testing Laboratory | Sigmatest

The Aggregate Crushing Value offers a related measure of the resistance of an average to crushing under a compressive load that is gradually applied. Test Method: IS: 9376-1979, IS: 2386 (P-4)1963. Drying Shrinkage:

Aggregate Crushing Value Test - Learning Technology

Aug 27, 2019· The aggregate crushing value is a numerical index of the resistance of an aggregate to crushing under a gradually applied compressive load. It is expressed as the percentage by mass of the crushed (or finer) material obtained when the test sample is subjected to a specified load under standard conditions. Aggregates with lower crushing value ...

Determination of Aggregate Impact Value - Impact Test on ...

The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure o f Aggregate Impact Test The test sample consists of aggregates sized 10.0 mm 12.5 mm. Aggregates may be dried by heating at 100-110° C for a period of 4 hours and cooled.

Aggregate Crushing Value - Civil Engineering Portal ...

AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) – 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes – 12.5mm, 10mm and 2.36mm Procedure to determine Aggregate Crushing Value i) The aggregates passing through 12.5mm […]